flow rate sensor

1. Translation of Flow Meter Specifications: Performance Specifications Accuracy (linear ranges) Factory tested ¹ ± 0.5% of flow rate Factory testing accuracy (linear range)+0.5% flow rate ¹ Typical field installation ² ± 1 to 2% of flow rate Typical field installation ²+12% flow rate repeatability ± 0.1% of flow rate repeatability+0.1%, flow rate response time adjustable from 0.3 to 30 seconds ¹ Factory test conditions: water at 70 ° F, flow velocity>1 ft/sec on a 6 "stainless steel pipe ¹ Factory test conditions: 70 ° C Water, flow rate" 1 foot/second, press 6 "stainless steel pipe ²Field performance is dependent on the accuracy of the pipe"s internal diameter and wall thickness measurements, as well as straight run conditions² The performance relies on accurate measurement of the inner diameter and wall thickness of the pipeline, as well as the operating specifications for direct operation. The applicable pipeline sizes are 2 to 100 "(50 to 2540 mm) and 2100" (1950 to 2540 mm) Measurable fluids Most common liquids from waste water to petrochemical products The most common liquid petrochemical product that can be measured from wastewater is Measurable Flow Velocity Liquid -40 to 40 ft/sec (-12 to 12 m/sec) Measurable Flow Velocity Liquid -40 to 40 ft/s (12-12 m/sec) Process Pressure Not applicable Process pressure Not applicable Environmental temperature limit -40 to 140 ° F (-40 to 60 ° C) Normal temperature limit -40 to 140 ° F (-40 to 60 ° C) Process temperature limit Standard 40 to 250 ° F (-40 to 121 ° C) High temperature option 40 to 400 ° F (-40 to 205 ° C) High temperature selection from 40 to 400 ° F (below -40 to 205 ° C), ambient humidity limit up to 95% RH, non condensing air humidity up to 95% rhodium limit, non condensing power requirements Field configurable for AC or DC 12-24 VDC, power demand configuration for AC or DC 12-24 vinylidene chloride 115 VAC, 50/60 Hz (± 10%) 115 VAC, 50/60 Hz (+10%) 230 VAC, 50/60 Hz (± 10%) 230 VAC, 50/60 Hz (+10%) 230 VAC, 50/60 Hz (+10%) Power consumption Less than 5 W Input/Output modules 4 to 20 mA output Field configurable as a 2-wire active or passive transmitter, 800 Ω maximum resistance input/output module 4 to 20 racecourse outputs can be configured as 2-wire active or passive transmitters, with a maximum resistance of 800 ohms Frequency output Field configurable for 0 to 1,000 Hz or 0 to 10,000 Hz output, 20 mA max (50% duty cycle) Out of town configuration with output frequency of 1000 Hz or 0010000 Hz, output of 20 marmax (50% duty cycle), Dual relay output of 175 V, ¼ A switch, 1 A cargo current, 0.2 Ω resistance, dual relay output of 175, fifth ¼ one turn, using a 0.2 Ω resistor RS485 interface Master/slave configuration, supports 57.6 kbd communications up to 1000"RS485 Interface master/slave configuration, supports up to 1000 communication joints 57.6 "RS232 interface supports up to 57.6 kbd communication (19.2 kbd @ 50") RS232 interface supports up to 57.6 communication joints (19.2 kbd @ 50 ") Dual RTD input Accepts two 1000 Ω RTD inputs for BTU measurement Even accepts two 1000 Ω resistor inputs Resistance measurement inputs BTU Data logger Non-volatile storage of 100,000 time/date stamped data points, selectable from 1 to 1,000 seconds. Data recording non-volatile storage 100000 times/date printing data points, selected from October 1st to 1000 seconds Connections with PC serial port for data retrieval Physical Specifications Materials Wetted parts None Non wetted

『SILVER Official Website SERVICE』